How to install rear view camera – How to Install a Rear View Camera in Your Car – AutoPumpkin Official Support Center

How to Install a Rear View Camera in Your Car – AutoPumpkin Official Support Center

Installing a rear -view camera in your car can help prevent mishaps when you’re backing up your vehicle. This device is especially helpful if you’re backing up larger vehicles such as trucks and RVs, because it allows you to view people and items behind your vehicle that cannot be easily seen. Learn how to install a rear-view camera in your car to help you see behind you and prevent potentially damaging accidents.

Steps:

1. Research and purchase the type of rear-view camera installation system that is best for your car. If you are unsure of what type would be best, you can ask for advice at a local auto repair shop.

2. Disconnect the vehicle’s battery by pulling off the negative cable.Wire the camera to the battery according to the instructions provided with your kit. The battery acts as the camera’s power source

3. Install your rear-view camera monitor. There are several possible locations to install the monitor. The most common locations are on the dashboard or sun visor. The monitor will allow you to view anything behind your car before you back out, so it should be placed in a location that is convenient when driving.

4. Use a drill to install the camera.Mount the camera on the bumper, license plate, or other location at the rear of the vehicle. The kit will include all the necessary mounting hardware. Attach the camera’s power wire to the back-up light power wire on your car. If you purchased a wireless camera, you do not need to wire the camera. Reconnect the car battery.

5. Test the camera before attempting to drive with it.Make sure you can clearly see what is behind the car. Turn on the camera and monitor, place an immovable object behind the car, put the car in reverse but keep your foot on the brake, and verify that you can see the object in the monitor.

Tips:

  • Many rear-view cameras are designed to only work when you have the car in reverse. The manufacturer may provide instructions on how to rewire it to work anytime the car is turned on.
  • Before you permanently mount the monitor, try different locations to make sure it stays put and that you are happy with where it is located. Most kits come with double-sided tape, screws, and other mounting hardware.
  • You can mount the camera on the car’s plastic bumper if you want to avoid drilling into your car’s sheet metal.

Source: wikihow.com

For more Android car stereos, please visit autopumpkin.com

Related Posts

  • Car Stereo Installation Guide

    By Robert Ferency-Viars This installation guide walks you through the process of installing a new Android car stereo. Please read over these guidelines before beginning the installation in order to give yourself an idea of what to expect. Tools Needed (depending upon vehicle) Remove the factory stereo When installing a new stereo in your car, your first step will be to remove the old stereo. Pay close attention to the steps involved, for the process for installing your new stereo will be the same, but in reverse. For detailed information on how to remove the factory stereo in a specific vehicle, refer to your Crutchfield MasterSheet™ instructions, if available. They will walk you through the process step-by-step. Otherwise, you may use the general guidelines below. Before you begin, start by setting the parking brake and removing the negative cable from the car battery to prevent accidentally short circuiting something. Disconnect your battery’s negative terminal before any installation job to protect your electrical system.. Your factory stereo will be mounted in one of two ways: secured in a metal mounting sleeve by spring clips bolted to the dash with brackets…

  • Differences between Single DIN and Double DIN Android Car Stereo

    If you want to buy an aftermarket Android 4.4 car stereo, you should base on your car’s year, make and model. Normally, aftermarket head units are rectangular and the standard car stereo size is referred to as single DIN. Most cars have single DIN stereo slots. The measurement of a standard single DIN slot is 50mm height by 178mm width. Most car radios will slide directly into the single DIN slot without requiring an additional adapter kit. However, some DIN models may require an installation kit. The second most common car stereo slot size is the double DIN. Double DIN slots are twice as tall as the standard single DIN slots, but they have the same width as single DIN stereos. We carry double DIN car stereos that slide directly into the double DIN slot. If you have the space, double DIN models are great because they usually feature LCD monitors for video playback and GPS navigation. Actually, the double DIN Android head units have become more popular: many vehicle manufacturers (especially of Asian cars) created a DIN CD player for use with a DIN cassette/radio unit. The main advantage to an aftermarket double DIN is that it’ll look better in the dash of a vehicle that uses a stock double DIN head unit. A larger head unit can have larger controls and a larger display, which making it easier to use. The best in-dash mobile video and navigation units are double DIN, because they don’t require a flip-out mechanism for the viewscreen. Regardless of classification (single DIN, double DIN, etc.), the stereo’s depth is unique for each model. The installation may require some customization if your vehicle has a relatively shallow cavity. Though you may wish to perform custom installs, it’s always wisest to choose a model that will fit your car perfectly. Check out our website to find out what will exactly fit your vehicle. This will save you a lot of time, money and hassle when it comes time to install your car stereo.

  • How to Install an Android Car Stereo

    First, turn off the electricity to the machine by removing the live battery wire from its station. After disconnecting the battery, you’ll need to take off the trim boards enveloping your car stereo. Each car just a tiny bit unique here. Next, you need to dispatch the previous head unit directly out until the wires connected to the back are accessible. Unplug the cord, discharge the cabling harness and proceed to remove the antenna cable by unscrewing it. The cabling harness is the structural fastener that integrates all of the cabling for the sound system into an individual connection. The new head unit you have purchased should have included an adapter that matched the factory installed cabling. The end of the cabling on the end, should have four to eight colored wires coming from the back. There should be two such wires that plug to each speaker; one positive one negative. Most negatives are shown with a black stripe while positives are generally either solids or have a white stripe. If your new car DVD player does not come with an adapter that works with the harness in the dash, you need to purchase a cabling harness kit. The new harness will have to be plugged into the new stereo. Match the colored wire to its match and put them together. After having the wires connected to their proper match, the stereo should be ready to install. Hold the system to the dash to plug the proper connections into the back. You can pause and test what you have done to make sure you have correctly pared the wires. Once you find that everything is in order; proceed to carefully push the unit all the way into the dash and replace the screws. After the stereo is mounted correctly, put the trim boards back up and reattach everything holding them in place. Finally, you got a new Android stereo for your car.

news.autopumpkin.com

how to install a new rear view camera on car ~ Oem Navigation System-Car Stereo Installation Guide DIY

what is a car rear camera?how can we install it?

a rear camera is a little device in car dvd player.All of the Car DVD player support the rear camera input and support automatically rear view when the car turn to reverse.

and the following article is the details of how to install it:

First of all,you should make a decision where you want to set up the rear-view camera. Most of driving put them in the plastic bumper so they don’t have to drill into the car’s sheet metal.But for some special rear camera,it is no need to drill a hole of the bumper,because they are design for the special car,it fit to the back light exactly,such as the Rear camera Suzuki Swift CM036,it will be very good look and hidden as original after installation.But if you can not sure about which oen to set up to your vehicle,It does not matter,the rear camera cm110 or Car Rear Camera License plate cm550 will be ok.

more over,drill a hole for the camera. Check the Installation Guide ( Mounting Instructions ) to see what size will suit you. make sure that the hole is not too large or the camera will fall out.

Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight.

Attach the cable from the camera to a wireless backup lights on your vehicle.  You’ll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to connect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the vehicle in reverse.Check this photos carefully if you are not sure:

between auto dvd gps and camera:
«video output» from camera connect to «camera in» of the auto dvd gps

between auto dvd gps and vehicle
«Back control wire» from auto dvd gps connect to the «switch wire of the back lamp» of the vehicle

between rear camera and car
«power cable» (red) from camera connect to the «power cable of the back lamp» of the vehicle(Some  vehicles such as bmw need to connect a Relay to help the camera power on when reversing)
«GND»(black) wire from camera connect to the «GND» wire of the back lamp of the vehiche

Route the camera’s output wire to the rear-view monitor and connect the wire to the monitor’s input.

Reconnect the battery, start the vehicle and put the car in reverse. The rear-view monitor should turn on and give you a view of what’s behind you.

that is the Whole Solution for how to install car rear camera.it seems not difficult to Operating by yourselves.but,in a word,safety first.take care of yoursevles while installing the camera device.

how-to-gps.blogspot.com

How to Install a Rear-View Camera in Your Car

How to Install a Rear-View Camera in Your Car

by Contributor

Rear-view cameras are especially useful in tight parking lots, dark areas or in places where children might be running around. You can install as many of these cameras as you want, though one or two is usually enough.

Disconnect the battery cables from the battery. Check the vehicle’s repair manual to find out what size wrench to use. Leave the disconnected cables a safe distance from the battery posts.

Decide where you want to install the rear-view camera. Most people put them in the plastic bumper so they don’t have to drill into the car’s sheet metal.

Drill a hole for the camera. Check the installation instructions to see what size drill bit to use. Don’t make the hole too large or the camera will fall out.

Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight.

Attach the camera’s power wire to the backup-light power wire on your car. You’ll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to reconnect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the car in reverse.

Route the camera’s output wire to the rear-view monitor and connect the wire to the monitor’s input. For installation of the monitor, see the monitor’s installation instructions.

Reconnect the battery, start the car and put the car in reverse. The rear-view monitor should turn on and give you a view of what’s behind you.

About the Author

This article was written by a professional writer, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. To submit your questions or ideas, or to simply learn more, see our about us page: link below.

itstillruns.com

Отправить ответ

avatar
  Подписаться  
Уведомление о