How to hang things on concrete walls – How to hang things on concrete walls — Freckle & Fair

How to Hang Things on a Concrete Wall


Finishing off an existing basement room is one way to add living space
to a house. Decorating a basement room, or another space with concrete
walls, poses special challenges. Applying a sticky hanger is not
always the best option, as the moisture that makes its way through the
concrete can loosen the adhesive, causing the object to ultimately
fall. Hanging pictures will take more than a hammer and nail, yet it
is not a difficult task.Difficulty:Moderately EasyInstructions
Things You’ll Need
Brick hook
Bendless nails
Drill with
1/8-inch masonry drill bit
Hammer

Visit the
hardware store and purchase a brick hook with bendless nails, designed
specifically

Drapes over a concrete wall, reuqires special tools to make the holes
in the wall, for the anchors you need.Difficulty:ModerateInstructions
Things You’ll Need
Drapes
Drill
Special Drill
Bit
Anchors

Hey All,To drill a hole into a
concrete wall you actually need a special concrete drill bit. A
regular drill bit will break and/or not do the trick.
1: First
thing to do is figure what size anchors you are going to use quarter
inch, half inch etc. This will vary, on the size of the rod you
purchase.
The Drill Bit2: Once you have the size you want you will
then want to go over to the drill bits and pick up this type of bit.
It is called a masonry drill

Home & Garden

While a building with concrete walls is sturdy, it can often make a
room feel desolate if left bare. You may wish to make the room feel
more inviting by adding photos to the walls. However, putting a nail
in a concrete wall can be difficult, and if you aren’t careful you can
crack the concrete. An alternative method that doesn’t require holes
in the wall is to use mounting tape.

Home & Garden

Hanging cabinets is a DIY project that can be handled by most DIYers.
Attaching them to concrete is only slightly more challenging. You will
need a drill with a 3/16-inch mason’s bit, a level, a tape measure and
a few 1 1/2-inch Tapcon-type concrete anchors. It also helps to have a
little assistance when hanging cabinets. Preparing the CabinetThe
first step is to create a French cleat, which is a board split down
the middle on a 45-degree angle. The two mitered edges fit together to
pull the cabinet into the wall snugly. Cut the cleat from an 8-inch
strip of 3/4 inch plywood as long as the inside width of the back of
your cabinet. Set your table saw blade on 45 degrees and rip the
plywood

Home & Garden

Concrete block walls provide a unique challenge to hanging mirrors,
because you cannot simply nail or screw into them. Instead, you must
use specialized expansion anchors, which expand when you insert a
screw. This expansion causes the anchor to hold tight to concrete.
Once the anchors are in place, the process becomes the same as hanging
a mirror on any other wall, though you must use screw-in brackets
instead of those with nails.Difficulty:Moderately EasyInstructions
Things You’ll Need
Mirror
Level
Pencil
Anchors
Drill
and masonry bit
Hammer
Mirror brackets and screws
class=»error»>Hold the mirror against the wall in the location where
you want to hang it.

Home & Garden

Installing curtains and rods on a concrete wall is not dissimilar to
installing them on drywall or wood. The major difference is that you
won’t be able to use the screws included with your curtain rod set
when you’re ready to install the curtains. These screws are typically
meant for softer surfaces, such as drywall or wood. If you have
concrete walls, this does not preclude you from buying standard
curtain rod sets — you’ll just need to replace the screws with ones
meant for concrete.Difficulty:Moderately EasyInstructions Things
You’ll Need
Measuring tape
Curtain rod
set
Pencil
Carpenter’s level
Drill
Concrete screws
class=»error»>Measure the window. This wil

Home & Garden

Concrete walls are capable of supporting heavy items provided that the
proper anchoring device is installed. Shelving brackets and hooks that
are constructed of strong steel mean little if the anchor which
fastens them to the concrete wall is too weak to bear the weight.
Installing strike anchors that expand inside the concrete is one of
the best ways to secure heavy things on concrete walls. You can get
the job done with the proper tools, materials and basic masonry and
power tool knowledge.Difficulty:Moderately ChallengingInstructions
Things You’ll Need
Safety glasses
Ear
protection
Ruler
Hammer drill
Masonry drill bit
Masking
tape
Shop-vac
Hand blower
Str

Home & Garden

In reading this article you will learn how easy and how fun it is to
do things yourself. You will learn how to hang items, such as
paintings, pictures, candle holders and even fountains, on a concrete
wall.Difficulty:ModerateInstructions Things You’ll Need
safety
glasses
dust mask
sledge hammer
pliers
center punch
class=»error»>Step 1
this step is very important so that you make
a straight hole into the concrete wall. use a center punch and make a
starter hole for the drill bit.
Step 2
In this step you will
drill a hole into the wall, start slow then increase the speed as you
go.
Step 3
Using a stop collar drill a hole as deep as the
anchor

Home & Garden

bighow.org

How to Hang Heavy Things on Concrete Walls

It is important to use the proper procedure and materials when hanging
heavy paintings on a concrete wall; otherwise, the painting can fall
and cause injury or damage. The challenge posed by hanging on a
concrete wall as opposed to drywall or plaster is the density of the
concrete. The advantage of concrete is that once the painting is hung,
concrete is much less likely to loosen any
fasteners.Difficulty:Moderately EasyInstructions Things You’ll
Need
Hanging wall brackets
Phillips screwdriver
Tape
measure
Pencil
Electric drill
Masonry bit
Cement wall
anchors
Hammer

Install the sections of the
brackets for the painting on the top and bottom o

Home & Garden

The most available space for hanging a heavy duty shelf is often in a
garage or basement, the epicenter of heavy duty item use. With these
locations, concrete, plaster or brick walls are much more common than
in the rest of the home. As such, installing a heavy shelf into these
materials requires a substantially stronger set of materials, but the
basic steps of installation are very similar. With the proper
materials, shelving installed into concrete walls can bear extremely
heavy loads.Difficulty:Moderately EasyInstructions Things You’ll
Need
Shelf board
Brackets
Wood screws, 1-inch
Hammer
drill
Phillips drill bit
Carpentry level
Pencil
Masonry
drill bit, 3-in

Home & Garden

When hanging heavy pictures, it is best to locate a stud and hang the
picture there. Sometimes, however, studs are not located where you
would like to hang your picture. In this case, there is hardware
available to help support your picture so that it does not harm your
plaster wall. Installation on a plaster wall is not any different than
installation on a drywall wall. Plaster has a much higher chance of
cracking or flaking around the nail site,
however.Difficulty:EasyInstructions Things You’ll Need
1/8-inch
drill bit
Drill
Toggle bolt
Screwdriver
class=»error»>Make a pencil mark on the wall where you would like to
hang your picture.
Use a 1/8-inch drill bit and

Home & Garden

Until the late 1950s, most homes had lath-and-plaster walls instead of
the simpler sheets of drywall that are common in most newly
constructed houses. The lath-and-plaster method involved nailing small
wooden strips of cedar — the lath — onto a 2 x 4 frame and then
covering that with one to three layers of plaster to create a strong,
solid wall. Displaying heavy pieces of art on these walls can cause
damage to the plaster if you hang the artwork
incorrectly.Difficulty:Moderately EasyInstructions Things You’ll
Need
Stud finder
Pencil
Drill bit
Cordless drill
Wood
screw
Wall anchor
Hammer
Nail

Use a stud
finder to locate the stud in the wall

Home & Garden

Heavy picture shelves that hang on a wall do so with the aid of
brackets that are screwed into the wall. Hanging these types of
shelves on a wall constructed of Sheetrock can be a challenge. If the
screws are inserted directly into the Sheetrock, they will eventually
work their way out, causing the shelf to fall. The screws must be
anchored into the Sheetrock in order to ensure that they remain
securely attached to the wall.Difficulty:Moderately EasyInstructions
Things You’ll Need
Level
Pencil
Electric drill
Masonry
drill bit
Plastic wall anchors
Hammer
Driver bit
class=»error»>Hold the shelf on the wall in the desired
location.
Place a level on the shelf

Home & Garden

Hanging curtains on a concrete wall requires the use of anchors to
hold the curtain rod in place. Simply drilling a screw into a drilled
hole will not work; typical wall screws will not hold in concrete.
There are multiple types of wall anchors that all have specific uses
and weight ratings. These are things to consider when you purchase the
anchors to hold the rods and curtains in place. Purchase anchors
designed for concrete, and that can also bear the weight of the
curtains.Difficulty:Moderately EasyInstructions Things You’ll
Need
Alligator anchors
Tape measure
Pencil
Masonry drill
bit
Hammer drill
Screwdriver

Measure from
one side of the windo

Home & Garden

Simply hanging something heavy on a plaster wall can result in damage
to the wall and the object if you don’t tap into the supporting
structure behind the plaster. Though there are several methods of
locating studs, or supports behind the wall, the most reliable is
using a magnetic stud finder. Once you’ve done that, hanging a heavy
object like a large mirror, television or work of art becomes a safer
and simpler task.Difficulty:Moderately EasyInstructions Things
You’ll Need
Stud finder
Drill
Anchor bolts
class=»error»>Move the stud finder over the plaster wall across the
spot where the heavy object will hang. When finder passes over a nail,
the magnet will react. Mark

Home & Garden

bighow.org

How to Hang Items On a Concrete Wall


In reading this article you will learn how easy and how fun it is to
do things yourself. You will learn how to hang items, such as
paintings, pictures, candle holders and even fountains, on a concrete
wall.Difficulty:ModerateInstructions Things You’ll Need
safety
glasses
dust mask
sledge hammer
pliers
center punch
class=»error»>Step 1
this step is very important so that you make
a straight hole into the concrete wall. use a center punch and make a
starter hole for the drill bit.
Step 2
In this step you will
drill a hole into the wall, start slow then increase the speed as you
go.
Step 3
Using a stop collar drill a hole as deep as the
anchor

Drapes over a concrete wall, reuqires special tools to make the holes
in the wall, for the anchors you need.Difficulty:ModerateInstructions
Things You’ll Need
Drapes
Drill
Special Drill
Bit
Anchors

Hey All,To drill a hole into a
concrete wall you actually need a special concrete drill bit. A
regular drill bit will break and/or not do the trick.
1: First
thing to do is figure what size anchors you are going to use quarter
inch, half inch etc. This will vary, on the size of the rod you
purchase.
The Drill Bit2: Once you have the size you want you will
then want to go over to the drill bits and pick up this type of bit.
It is called a masonry drill

Home & Garden

While a building with concrete walls is sturdy, it can often make a
room feel desolate if left bare. You may wish to make the room feel
more inviting by adding photos to the walls. However, putting a nail
in a concrete wall can be difficult, and if you aren’t careful you can
crack the concrete. An alternative method that doesn’t require holes
in the wall is to use mounting tape.

Home & Garden

Hanging cabinets is a DIY project that can be handled by most DIYers.
Attaching them to concrete is only slightly more challenging. You will
need a drill with a 3/16-inch mason’s bit, a level, a tape measure and
a few 1 1/2-inch Tapcon-type concrete anchors. It also helps to have a
little assistance when hanging cabinets. Preparing the CabinetThe
first step is to create a French cleat, which is a board split down
the middle on a 45-degree angle. The two mitered edges fit together to
pull the cabinet into the wall snugly. Cut the cleat from an 8-inch
strip of 3/4 inch plywood as long as the inside width of the back of
your cabinet. Set your table saw blade on 45 degrees and rip the
plywood

Home & Garden

Finishing off an existing basement room is one way to add living space
to a house. Decorating a basement room, or another space with concrete
walls, poses special challenges. Applying a sticky hanger is not
always the best option, as the moisture that makes its way through the
concrete can loosen the adhesive, causing the object to ultimately
fall. Hanging pictures will take more than a hammer and nail, yet it
is not a difficult task.Difficulty:Moderately EasyInstructions
Things You’ll Need
Brick hook
Bendless nails
Drill with
1/8-inch masonry drill bit
Hammer

Visit the
hardware store and purchase a brick hook with bendless nails, designed
specifically

Home & Garden

Look in an unfinished basement, on an exterior concrete wall or other
area where concrete is a prevalent wall surface and you are likely to
see electrical boxes mounted directly on the surface of the wall.
Mounting these boxes so that they are recessed in the concrete is
nearly impossible, which is why you are likely to see the boxes
exposed. With the right tools, mounting electrical boxes on a concrete
wall is a quick process.Difficulty:EasyInstructions Things You’ll
Need
Marker
3/16-inch hammer drill bit
Hammer
drill
Masonry screws
Cordless drill
Safety glasses
class=»error»>Hold the electrical box up to the wall. Make a mark on
the wall through each mounting

Home & Garden

The most available space for hanging a heavy duty shelf is often in a
garage or basement, the epicenter of heavy duty item use. With these
locations, concrete, plaster or brick walls are much more common than
in the rest of the home. As such, installing a heavy shelf into these
materials requires a substantially stronger set of materials, but the
basic steps of installation are very similar. With the proper
materials, shelving installed into concrete walls can bear extremely
heavy loads.Difficulty:Moderately EasyInstructions Things You’ll
Need
Shelf board
Brackets
Wood screws, 1-inch
Hammer
drill
Phillips drill bit
Carpentry level
Pencil
Masonry
drill bit, 3-in

Home & Garden

Installing curtains and rods on a concrete wall is not dissimilar to
installing them on drywall or wood. The major difference is that you
won’t be able to use the screws included with your curtain rod set
when you’re ready to install the curtains. These screws are typically
meant for softer surfaces, such as drywall or wood. If you have
concrete walls, this does not preclude you from buying standard
curtain rod sets — you’ll just need to replace the screws with ones
meant for concrete.Difficulty:Moderately EasyInstructions Things
You’ll Need
Measuring tape
Curtain rod
set
Pencil
Carpenter’s level
Drill
Concrete screws
class=»error»>Measure the window. This wil

Home & Garden

bighow.org

How to Hang Art on Concrete Walls

You may not be able to match rock star Steve Howe and his collection
of about 155 guitars, but even a modest collection of several guitars
can look impressive. Hanging guitars on the walls out in the open not
only displays their beauty, but also serves as a reminder to practice
regularly. When the walls are concrete, it takes a little more effort
to secure the guitars. Installing wooden bases gives the guitar hooks
something to attach to.Difficulty:ModerateInstructions Things
You’ll Need
Pieces of wood, 1-by-2-by-3-inches
Sandpaper
Wood
stain or paint
3/16-inch concrete screws, 2 inches long
Drill
with bits
Nut driver
Screwdriver
Goggles and breathing
mask

Home & Garden

Curtains can help to decorate any room, and the same is true of rooms
with concrete walls. Because the walls are solid, however, you cannot
simply screw into them. You must use expansion anchors, which are
designed to expand when a screw is inserted and physically lock
against the concrete. Each anchor can hold up to 30 pounds, making
them more than enough to support a curtain rod.Difficulty:Moderately
EasyInstructions Things You’ll Need
Curtain rod brackets with
screws
Pencil
Level
Measuring tape
Expansion
anchors
Drill
Masonry bit
Hammer
Screwdriver
Curtain
rod
Curtain

Hold one curtain rod bracket
against the wall next to the wind

Home & Garden

Concrete studs, columns and posts are common structural elements in
commercial and industrial buildings. Many architects of modern homes
and housing complexes also utilize concrete supports, often leaving
them exposed as an aesthetic architectural element. Concrete supports
have great strength, but when you want to hang something, the standard
nail and hammer will not cut it. From clocks to curtains, various
items are easily hung using expansion or molly anchors. Expansion and
molly anchors feature a screw with a sleeve. The sleeve encases and
helps to wedge the screw tightly into a pre-drilled
hole.Difficulty:ModerateInstructions Things You’ll Need
Molly
anchors
Tape measure

Computers

If you have concrete walls in your home or office, you don’t have
quite as many options when it comes to hanging wall decorations.
However, while you cannot use standard hangers like the ones you would
use to secure objects to wood or drywall, you can still hang stuff on
concrete walls. A few specialized pieces of hardware have been created
for the very purpose of hanging items on a concrete
surface.Difficulty:ModerateInstructions Things You’ll
Need
Adhesive fasteners
Masonry fasteners
Drill
Masonry
bit
Canned air
Flathead or Phillips drill bit
class=»error»>Adhesive FastenersDrill a hole, using a masonry bit of
the size recommended in the directions that come

Home & Garden

Hanging curtains on a concrete wall requires the use of anchors to
hold the curtain rod in place. Simply drilling a screw into a drilled
hole will not work; typical wall screws will not hold in concrete.
There are multiple types of wall anchors that all have specific uses
and weight ratings. These are things to consider when you purchase the
anchors to hold the rods and curtains in place. Purchase anchors
designed for concrete, and that can also bear the weight of the
curtains.Difficulty:Moderately EasyInstructions Things You’ll
Need
Alligator anchors
Tape measure
Pencil
Masonry drill
bit
Hammer drill
Screwdriver

Measure from
one side of the windo

Home & Garden

Concrete walls are capable of supporting heavy items provided that the
proper anchoring device is installed. Shelving brackets and hooks that
are constructed of strong steel mean little if the anchor which
fastens them to the concrete wall is too weak to bear the weight.
Installing strike anchors that expand inside the concrete is one of
the best ways to secure heavy things on concrete walls. You can get
the job done with the proper tools, materials and basic masonry and
power tool knowledge.Difficulty:Moderately ChallengingInstructions
Things You’ll Need
Safety glasses
Ear
protection
Ruler
Hammer drill
Masonry drill bit
Masking
tape
Shop-vac
Hand blower
Str

Home & Garden

Hanging a hook on a concrete block wall may seem impossible, but this
job is actually relatively easy and straightforward. Drilling through
the concrete does require some special tools, which are readily
available for purchase at your local hardware store. If you do not
want to purchase the tools, ask the store if they are available for
rental.Difficulty:Moderately EasyInstructions Things You’ll
Need
Hammer drill
Pencil
Masonry
bit
Screwdriver
Hammer

Hold the hook on the
concrete block wall. Place a mark on the wall at the screw holes’
locations with a pencil. Set the hook aside.
Drill a pilot hole
through each mark, using a hammer drill with a ma

Home & Garden

bighow.org

How to Hang Pictures on a Concrete Wall

Drapes over a concrete wall, reuqires special tools to make the holes
in the wall, for the anchors you need.Difficulty:ModerateInstructions
Things You’ll Need
Drapes
Drill
Special Drill
Bit
Anchors

Hey All,To drill a hole into a
concrete wall you actually need a special concrete drill bit. A
regular drill bit will break and/or not do the trick.
1: First
thing to do is figure what size anchors you are going to use quarter
inch, half inch etc. This will vary, on the size of the rod you
purchase.
The Drill Bit2: Once you have the size you want you will
then want to go over to the drill bits and pick up this type of bit.
It is called a masonry drill

Home & Garden

Hanging pictures on your walls can make any room more inviting. Having
concrete or hard walls should not inhibit you from decorating on any
wall that you so choose. However, in most instances, you would need a
drill and a masonry bit to set screws in concrete or cement walls.
That no longer is the case because you can now hang pictures on your
walls without needing a drill.Difficulty:Moderately EasyInstructions
Things You’ll Need
Hard-wall picture hangers
Hammer
class=»error»>Select the right hooks. Hard-wall picture hangers come
in a variety of sizes that will determine the load bearing ability of
the hooks. You can get the hooks at any hardware store.
Place the
hooks

Home & Garden

In block houses, it is necessary to use a special procedure when
hanging pictures on the walls. Because concrete is much harder than
wood or paneling, nails are not an option. Special nail-type items
have been developed that will allow you to hang your favorite picture
today.Difficulty:Moderately EasyInstructions Things You’ll
Need
Picture
Drill
3/16-inch masonry drill bit
Plastic or
metal anchors
Anchor hooks
Hanging wire
class=»error»>Drill a 3/16-inch diameter hole in the concrete with a
masonry bit. Insert a metal or plastic anchor.
Insert an anchor
hook—a screw with a picture hook attached to it—into the metal or
plastic anchor.
Hang your picture o

Home & Garden

Hanging cabinets is a DIY project that can be handled by most DIYers.
Attaching them to concrete is only slightly more challenging. You will
need a drill with a 3/16-inch mason’s bit, a level, a tape measure and
a few 1 1/2-inch Tapcon-type concrete anchors. It also helps to have a
little assistance when hanging cabinets. Preparing the CabinetThe
first step is to create a French cleat, which is a board split down
the middle on a 45-degree angle. The two mitered edges fit together to
pull the cabinet into the wall snugly. Cut the cleat from an 8-inch
strip of 3/4 inch plywood as long as the inside width of the back of
your cabinet. Set your table saw blade on 45 degrees and rip the
plywood

Home & Garden

Finishing off an existing basement room is one way to add living space
to a house. Decorating a basement room, or another space with concrete
walls, poses special challenges. Applying a sticky hanger is not
always the best option, as the moisture that makes its way through the
concrete can loosen the adhesive, causing the object to ultimately
fall. Hanging pictures will take more than a hammer and nail, yet it
is not a difficult task.Difficulty:Moderately EasyInstructions
Things You’ll Need
Brick hook
Bendless nails
Drill with
1/8-inch masonry drill bit
Hammer

Visit the
hardware store and purchase a brick hook with bendless nails, designed
specifically

Home & Garden

In reading this article you will learn how easy and how fun it is to
do things yourself. You will learn how to hang items, such as
paintings, pictures, candle holders and even fountains, on a concrete
wall.Difficulty:ModerateInstructions Things You’ll Need
safety
glasses
dust mask
sledge hammer
pliers
center punch
class=»error»>Step 1
this step is very important so that you make
a straight hole into the concrete wall. use a center punch and make a
starter hole for the drill bit.
Step 2
In this step you will
drill a hole into the wall, start slow then increase the speed as you
go.
Step 3
Using a stop collar drill a hole as deep as the
anchor

Home & Garden

Hanging artwork turns a house into a home; however, not all walls are
made of plaster and drywall. In urban areas, walls can be made of
brick or concrete and present a challenge when decorating. Concrete
screws provide a solution to this problem, and are available at any
hardware store. Concrete screws are stronger than wood screws, and
ensure your artwork is hung securely.Difficulty:ModerateInstructions
Things You’ll Need
Power drill
Masonry bit
Screwdriver
bit
Concrete screw

Drill a 3/16 inch to 5/16
inch diameter hole into the concrete using a masonry bit. The hole
will be smaller than the concrete screw.
Insert the screwdriver bit
into the drill.

Home & Garden

bighow.org

How to Hang Things on Your Walls

The warm glow of glass block walls adds light, depth and richness to
any decor, but it can present decorating challenges. You can hang
decorative items, artwork or shelves on glass block if you are careful
and use common sense. Before doing so, be sure the items you are
hanging will not detract from the bold statement the glass block
makes. Remember, any drilling cannot be undone or repaired, and if
done incorrectly can even crack or shatter the blocks. However, with a
thoughtful approach and a little caution you can achieve professional
decorating results.Difficulty:EasyInstructions Things You’ll
Need
Level
Steel tape measure
Felt-tip marker
Denatured
alcohol
Clean clo

Home & Garden

You just purchased a beautiful piece of wall art or other decorative
item—one that would look great hanging on the brick wall over your
fireplace. Now you’re wondering how to hang it on the bricks.
Fortunately, there is a simple way to hang items on brick
walls.Difficulty:Moderately EasyInstructions Things You’ll
Need
Drill
Masonry bit
1½-inch masonry screws
class=»error»>Insert a masonry bit into your drill. Refer to the drill
manufacturer’s instructions to determine which size bit to use for
your screws. Tom Silva of thisoldhouse.com recommends using
1½-inch masonry screws.
Drill a hole directly into one of the
bricks and then blow away any dust. Do not

Home & Garden

Plaster walls are often found in older homes. Plaster’s adaptability
to paint, whitewashing, stenciling or wallpaper is one of the reasons
for its popularity. Although plaster has its benefits, hanging things
on the walls sometimes damages the wall or causes a section of the
plaster to crumble. You can avoid these problems by using the correct
techniques when hanging items on the walls.Difficulty:Moderately
EasyInstructions Things You’ll Need
Stud finder
Adhesive
tape
Electric drill and drill bit
Hammer and
nails
Screwdriver and screws

Locate the studs
in the walls. These are upright structural posts that are typically 16
inches apart. Use a stud fin

Home & Garden

The walls of a mobile home are put up in panels with strips tacked
between the seams. With no wooded studs behind these panels, hanging
pictures and other items on the walls can be a challenge, especially
if they are heavy. However, it is possible, with the help of some
special hardware.Difficulty:Moderately EasyInstructions Things
You’ll Need
Stick-on hangers
Thin-wall
anchors
Drill
Nail
Wall putty
Interlocking adhesive
strips
Pencil

Attach stick-on hooks to the wall
for lightweight items such as small pictures. Pull the paper cover off
the back of the hook. Press the hook against the wall in the location
where you wish to hang the item.
Us

Home & Garden

Cement walls can give your home a modern feel you may find attractive,
but cement walls can make it difficult to hang a picture or a wall
decoration. Don’t let concrete walls stop you from hanging your wall
decor, though. You do not have to live with bare walls just to enjoy
the feel of authentic cement walls in your home. With special
materials, it is possible to hang items on cement
walls.Difficulty:Moderately EasyInstructions Things You’ll
Need
Hook and loop tape
Soap
Water
Expansion
anchor
Drill
Cement drill bit
Screws
class=»error»>Items Under 10 PoundsPurchase hook-and-loop tape.
Hook-and-loop tape uses special technology (commonly referred to by
the p

Home & Garden

Concrete walls are capable of supporting heavy items provided that the
proper anchoring device is installed. Shelving brackets and hooks that
are constructed of strong steel mean little if the anchor which
fastens them to the concrete wall is too weak to bear the weight.
Installing strike anchors that expand inside the concrete is one of
the best ways to secure heavy things on concrete walls. You can get
the job done with the proper tools, materials and basic masonry and
power tool knowledge.Difficulty:Moderately ChallengingInstructions
Things You’ll Need
Safety glasses
Ear
protection
Ruler
Hammer drill
Masonry drill bit
Masking
tape
Shop-vac
Hand blower
Str

Home & Garden

When redecorating a room, an empty wall presents a wealth of design
opportunities. The color and texture that you choose for it makes a
significant impact on the overall look of the space, but the items
that you choose to hang on it can make an even more dramatic
statement. You have a variety of options when selecting wall hangings,
ranging from simple to ornate, so you can add character and
personalize your room in a way that matches the rest of your decor.
PhotosSome of the most personal wall hangings that you can use to
decorate a room are framed photographs. You can hang family photos to
show your children as they grow, or travel back through your family’s
history to showcase black an

Home & Garden

bighow.org

How to Hang Things on Glass Block Walls

Builders like to use drywall or Sheetrock to build walls because it’s
relatively easy to work with, goes up fast and it’s cheap (OK
inexpensive). However, drywall has some drawbacks to a homeowner. It’s
easy to dent and scuff and because it’s essentially made from gypsum
powder and paper, which isn’t strong enough to hold a heavy object,
like a shelf, a mirror or a large picture. Luckily, you can get
specialized hangers at your home or hardware store that will allow you
to hang or mount heavy things on your walls or even your
ceiling.Difficulty:ModerateInstructions Things You’ll
Need
Drywall hangers (various types, see
below)
Drill
Hammer
Screwdriver
Tape measure
Pen

Home & Garden

You just purchased a beautiful piece of wall art or other decorative
item—one that would look great hanging on the brick wall over your
fireplace. Now you’re wondering how to hang it on the bricks.
Fortunately, there is a simple way to hang items on brick
walls.Difficulty:Moderately EasyInstructions Things You’ll
Need
Drill
Masonry bit
1½-inch masonry screws
class=»error»>Insert a masonry bit into your drill. Refer to the drill
manufacturer’s instructions to determine which size bit to use for
your screws. Tom Silva of thisoldhouse.com recommends using
1½-inch masonry screws.
Drill a hole directly into one of the
bricks and then blow away any dust. Do not

Home & Garden

Plaster walls are often found in older homes. Plaster’s adaptability
to paint, whitewashing, stenciling or wallpaper is one of the reasons
for its popularity. Although plaster has its benefits, hanging things
on the walls sometimes damages the wall or causes a section of the
plaster to crumble. You can avoid these problems by using the correct
techniques when hanging items on the walls.Difficulty:Moderately
EasyInstructions Things You’ll Need
Stud finder
Adhesive
tape
Electric drill and drill bit
Hammer and
nails
Screwdriver and screws

Locate the studs
in the walls. These are upright structural posts that are typically 16
inches apart. Use a stud fin

Home & Garden

Drywall is usually fastened to the wall studs with drywall screws. But
with walls constructed of block, the drywall cannot be fastened
directly to the walls. Furring strips must first be attached to the
walls to provide wood to which the drywall can be fastened. Furring
strips are one-by-two inch strips of wood eight feet in length. The
strips are fastened to the wall every 16 inches just like studs in a
regular wall.Difficulty:ModerateInstructions Things You’ll
Need
Tape measure
Furring strips
Electric drill
Driver
bit
Circular saw
2-inch masonry screws
Utility knife
1
1/2-inch Drywall screws

Secure a furring strip in
the corner of the wall

Home & Garden

Cement walls can give your home a modern feel you may find attractive,
but cement walls can make it difficult to hang a picture or a wall
decoration. Don’t let concrete walls stop you from hanging your wall
decor, though. You do not have to live with bare walls just to enjoy
the feel of authentic cement walls in your home. With special
materials, it is possible to hang items on cement
walls.Difficulty:Moderately EasyInstructions Things You’ll
Need
Hook and loop tape
Soap
Water
Expansion
anchor
Drill
Cement drill bit
Screws
class=»error»>Items Under 10 PoundsPurchase hook-and-loop tape.
Hook-and-loop tape uses special technology (commonly referred to by
the p

Home & Garden

Concrete walls are capable of supporting heavy items provided that the
proper anchoring device is installed. Shelving brackets and hooks that
are constructed of strong steel mean little if the anchor which
fastens them to the concrete wall is too weak to bear the weight.
Installing strike anchors that expand inside the concrete is one of
the best ways to secure heavy things on concrete walls. You can get
the job done with the proper tools, materials and basic masonry and
power tool knowledge.Difficulty:Moderately ChallengingInstructions
Things You’ll Need
Safety glasses
Ear
protection
Ruler
Hammer drill
Masonry drill bit
Masking
tape
Shop-vac
Hand blower
Str

Home & Garden

When redecorating a room, an empty wall presents a wealth of design
opportunities. The color and texture that you choose for it makes a
significant impact on the overall look of the space, but the items
that you choose to hang on it can make an even more dramatic
statement. You have a variety of options when selecting wall hangings,
ranging from simple to ornate, so you can add character and
personalize your room in a way that matches the rest of your decor.
PhotosSome of the most personal wall hangings that you can use to
decorate a room are framed photographs. You can hang family photos to
show your children as they grow, or travel back through your family’s
history to showcase black an

Home & Garden

bighow.org

Отправить ответ

avatar
  Подписаться  
Уведомление о